calibration by measurement
英 [ˌkælɪˈbreɪʃn baɪ ˈmeʒəmənt]
美 [ˌkælɪˈbreɪʃn baɪ ˈmeʒərmənt]
网络 由量度校准
双语例句
- Graduation and calibration of surveying instrument for liquid scintillation counter by using β radioactivity certified reference material, and the accurate measurement of 3H or 14C have been finished.
利用β放射性标准物质刻度和校准液闪计数器测量仪器，并完成3H和14C活度的精确测量。 - The calibration coefficients calculated by this multi-point calibration method can increase the measurement accuracy, decrease the errors and improve the logging data quality.
采用此多点刻度法计算的刻度系数，可以提高测量精度，降低误差，改善测井资料质量。 - We can know if the calibration mode is disturbed by the environmental noise by the principle components analysis, which provide the physical basis for the explanation of measurement result and the optimization of the measurement method and the measurement condition.
对主成分进行分析可以为测量结果的解释和测量方法、测量条件的优化提供物理依据。 - And the influence of the uneven acoustic field upon the calibration is cancelled by the means of a reciprocal measurement technique.
在耦合腔中采用传递函数法进行双水听器接收复声压的一致性校准，并采用易地交换测量消除声场不均匀性的影响。 - Calibration Method by Laser for the Diameter Measurement Sensors
对径测量传感器的激光校准方法 - Measurement principle and method of CCD are introduced. The CCD calibration method is also provided. The measurement layout is testified to be optimized by a simulation analyse of mouse model measurement under the help of CCD.
说明了CCD的测量原理及测量方法，然后介绍了CCD坐标系和机床坐标系的统一，以一鼠标模型的测量为例，通过仿真分析证明了CCD测量规划优化的指导作用。 - A calibration device for IR target simulator developed by the 3rd Metering and Testing Institute is presented in this paper, with the emphasis on de-sign idea, measurement basis, structural component and calibration of system, er-ror analysis and measurement example.
本文着重介绍红外目标模拟器检定装置的设计思想、测量原理、系统组成、系统标定、误差分析和测量实例。 - Then, the calibration equations and coefficients are obtained, which are verified by experiments. The new calibration approach is applied to avoid the influence of the variation of the system gain versus frequency to guarantee the validity of the measurement apparatus.
利用所得到的校准系数对钢板地电流的测量结果进行校准，可避免测量放大器增益随频率的变化对测量结果的影响，保证了地电流干扰研究的实验检测手段和验证方法的有效性。 - Experimentation and Research for Calibration of Reentry Pressure Dead Weight Piston Gauge by Ultra-high Pressure National ( measurement) Standard
利用超高压力国家基准对返压活塞式压力计校准的试验研究 - The data acquisition is completed by single chip microcomputer, and the optimization of calibration coefficient and area calibration are made by PC computer, thus the measurement precision is greatly improved.
由单片机完成数据采集，PC机完成标定系数优化和面积的计算，从而进一步提高了测量精度。 - The calibration factors are also calculated by angle response function on the conditions. The results of measurement and calculation are of agreement within 10%.
用角响应函数方法，计算了实验条件下的刻度因子，结果与实验值在10%范围内符合。 - A camera calibration method based on polynomial linearity fit for distorted picture is used and proved by the experiment, which brings higher camera measurement accuracy.
采用了基于多项式的线性回归的摄像机标定方法来对畸变图像进行校正。通过QDU-Ⅰ型自动引导车摄像机标定实验，验证该标定方法可提高摄像机测量精度，满足自动引导车的使用要求。 - A new technical way of the calibration of vortex flowmeter has been proposed by means of measurement with analytical method, in order to reduce the axial size of calibration equipments, and the calibration costs.
提出了一种以测试手段和分析办法相结合的关于标定涡街流量计的新的技术途径，以缩短标定装置的轴向尺寸，降低标定费用。 - The calibration of laser confocal sub-system of online monitoring system was completed by standard sphere verification, and the measurement uncertainty of relative position of sphere centers introduced by measurement method was calculated, which perfected the quantitative indexes of instrument performance.
通过标准球检定法对在线监测系统的共焦测量子系统进行了精度标定，计算了因测量方法引起的测量球心相对位置的不确定度，完善了仪器性能的量化指标。 - Finally, the calibration method is proved tobe reasonable and accurate by experimental data and analysis of uncertainty of measurement results.
最后，通过实验数据和测量结果不确定度的分析证明了本论文所提出的校准方法的合理性和正确性，且能够满足汽车排气污染物检测用底盘测功机校准和溯源的要求。 - This paper studies the non-linear calibration method of measurement system by referencing the theory in Taguchi measurement quality engineering.
本文通过借鉴田口测量质量工程学的理论研究了非线性测量系统校准方法，包括周期校准方法和日常校准方法。 - Regarded the theodolite as a tool, the paper introduces the measuring principle of the angular distance between stars of optical navigation sensor calibration system which guided by the theodolite, and states the measurement procedures in detail, and presents the measured data.
本文以经纬仪为工具，阐述了基于经纬仪的光学导航敏感器标定系统星间角距的测量原理，详细介绍了测量步骤，给出了测量数据。 - The local method for map building method is studied, reasonable height model is used to remove surface noise. In this chapter, calibration results and stereo matching results are tested by depth measurement.
第五章，分析了理想双目立体视觉系统的深度测量误差模型，研究了局部地图的构建方法，采用合理的高度模型去除地表噪声。 - The global calibration of sensor coordinates is accomplished by coordinates measurement arm and laser tracker, improving calibrated precision and efficiency.
利用坐标测量臂和激光跟踪仪的大尺寸测量能力，对传感器坐标系进行全局校准，提高校准的精度和效率。